HardiePlank Lap Siding installation Questions

Welcome to your HardiePlank Lap Siding installation Questions

HardiePlank Lap Siding installation: What is the maximum spacing allowed for studs when installing HardiePlank lap siding?

16 inches on center

20 inches on center

24 inches on center

32 inches on center

HardiePlank Lap Siding installation: What is the minimum overlap for both face and blind nailing?

1 inch

1 1/4 inches

1 1/2 inches

2 inches

HardiePlank Lap Siding installation: What type of fasteners must be used for HardiePlank lap siding?

Copper

Aluminum

Corrosion-resistant, galvanized, or stainless steel

Any type of nail

HardiePlank Lap Siding installation: How should HardiePlank lap siding be stored prior to installation?

Any type of nailOn its side

Flat and kept dry and covered

In a vertical position

Outside to acclimate

HardiePlank Lap Siding installation: What is the minimum clearance from the ground to siding in sheltered areas?

1 inch

2 inches

6 inches

8 inches

HardiePlank Lap Siding installation: What should be done with the laminate sheet on ColorPlus® products?

Leave as is for protection

Remove immediately after installation of each course

Remove before installation

Paint over i

HardiePlank Lap Siding installation: What is the recommended paint type for factory-primed James Hardie products?

Oil-based paint

100% acrylic topcoats

Latex paint

Stain

HardiePlank Lap Siding installation: What is the minimum clearance required between roofing and HardiePlank lap siding?

1 inch

2 inches

1/4 inch

No clearance required

HardiePlank Lap Siding installation: Can HardiePlank lap siding be used in fascia or trim applications?

Yes

No

HardiePlank Lap Siding installation: What should be done if large areas of ColorPlus® Technology siding require touch-up?

Paint over the entire surface

Replace the damaged area with new siding

Use any touch-up paint available

Leave as is

HardiePlank Lap Siding installation: What is the minimum clearance above steps and decks to the siding?

1 inch

2 inches

4 inches

6 inches

HardiePlank Lap Siding installation: How should cutting stations be positioned when cutting HardiePlank lap siding outdoors?

So that airflow blows dust towards the user

So that airflow blows dust away from the user

Indoors only

Without concern for airflow direction

HardiePlank Lap Siding installation: What is the minimum clearance required from siding to the finished grade?

2 inches

4 inches

6 inches in the first 10 feet

No specific requirement

HardiePlank Lap Siding installation: What should be done with non-factory cut edges of ColorPlus® Technology siding?

Leave as is

Caulk

Treat with ColorPlus Technology edge coaters

Paint with any paint

HardiePlank Lap Siding installation: What is the maximum mean roof height for buildings for which James Hardie provides installation/wind load information?

45 feet

60 feet

85 feet

100 feet

HardiePlank Lap Siding installation: What is the minimum clearance required between HardiePlank lap siding and a path, slab, or steps?

1/4 inch

1/2 inch

1 inch

As required by IRC code

HardiePlank Lap Siding installation: What should be done with James Hardie products that may remain in contact with standing water?

Install as usual

Seal with waterproofing

Do not install

Elevate slightly above water level

HardiePlank Lap Siding installation: What is the minimum clearance required for horizontal flashing?

1/4 inch

1/2 inch

1 inch

2 inches

HardiePlank Lap Siding installation: What type of nailing is preferred for HardiePlank lap siding?

Face nailing

Blind nailing

Stapling

Screw nailing

HardiePlank Lap Siding installation: What should be done if James Hardie ColorPlus products get construction dust on them during installation?

Leave the dust as it is

Blow it off with high-pressure air

Wipe off with a wet soft cloth or soft brush and rinse

Use a chemical cleaner

HardiePlank Lap Siding installation: What is the minimum overlap for joint flashing?

1 inch

1 1/4 inches

1 1/2 inches

2 inches

HardiePlank Lap Siding installation: What should be done with the Z-flashing at the intersection of a roof and wall?

Caulk the edges

Leave a minimum 1/4 inch clearance

Paint over it

Seal with tape

HardiePlank Lap Siding installation: What is the minimum clearance required from the siding to gutters in sheltered areas?

1 inch

2 inches

6 inches

No specific requirement

HardiePlank Lap Siding installation: What should be done with the drip edge to prevent damage during installation?

Caulk the edges

Handle with extra care

Paint it

Remove it

HardiePlank Lap Siding installation: What is the minimum size of Z-flashing required above windows and doors?

4 inches x 4 inches

2 inches x 2 inches

1 inch x 1 inch

No specific size is required

HardiePlank Lap Siding installation: What should be done with the valley/shingle extension in relation to the fascia when gutters are present?

Extend shingles at least 1 inch out from the fascia

Flush with the fascia

Extend shingles at least 2 inches out from the fascia

No extension is required

HardiePlank Lap Siding installation: What is the minimum penetration required for screws into steel framing?

1 thread

2 threads

3 threads

4 threads

HardiePlank Lap Siding installation: What is the minimum clearance required from the siding to a deck?

1/4 inch

1/2 inch

1 inch

2 inches

HardiePlank Lap Siding installation: What is the minimum clearance required from the siding to mortar/masonry?

1/4 inch

1/2 inch

1 inch

2 inches

HardiePlank Lap Siding installation: What should be done with the water-resistive barrier before installing siding?

It should be painted

It should be installed according to local building code requirements

It should be removed

It should be covered with another layer of barrier

HardiePlank Lap Siding installation: What is the minimum thickness of OSB sheathing required for HardiePlank lap siding installation?

3/8 inch

7/16 inch

1/2 inch

5/8 inch

HardiePlank Lap Siding installation: What should be done if James Hardie siding products are installed wet or saturated?

Install as usual

Dry before installation

Expect no change

Expect shrinkage at butt joints

HardiePlank Lap Siding installation: What is the correct procedure for handling and cutting James Hardie ColorPlus® products?

Cut dry and clean with a dry cloth

Handle without gloves and cut using a power saw

Handle gently and wipe off any residue with a wet soft cloth

Cut using a chainsaw for efficiency

HardiePlank Lap Siding installation: What is the maximum mean roof height for which James Hardie provides wind load information without special consideration?

30 feet

45 feet

60 feet

85 feet

HardiePlank Lap Siding installation: What type of nailing should be used in high wind areas as required by code?

Blind nailing

Face nailing

Both blind and face nailing

Stapling

HardiePlank Lap Siding installation: What is the minimum clearance required between HardiePlank lap siding and a paved surface or path?

1 inch

2 inches

6 inches

As required by local building codes

HardiePlank Lap Siding installation: How should James Hardie products be carried to prevent damage?

Flat

On edge

Rolled up

Stacked with spacers

HardiePlank Lap Siding installation: What should be done with the edges and corners of HardiePlank lap siding to prevent breakage?

Tape them

Protect them

Paint them

Caulk them

HardiePlank Lap Siding installation: What is the correct procedure for installing HardiePlank lap siding over steel studs?

Use any standard nails

Use special steel stud screws

Glue the siding onto the studs

Use aluminum nails

HardiePlank Lap Siding installation: What is the minimum clearance required from the siding to the soil?

1 inch

2 inches

6 inches

8 inches

HardiePlank Lap Siding installation: What is the minimum lap for HardiePlank lap siding when blind nailing?

1 inch

1 1/4 inches

1 1/2 inches

2 inches

HardiePlank Lap Siding installation: What should be done with the Z-flashing above windows and doors?

Caulk the top edge

Leave a minimum 1/4 inch clearance

Paint over it

Install it flush with the siding

HardiePlank Lap Siding installation: What is the minimum clearance required from the siding to a roof?

1 inch

2 inches

1/4 inch

No clearance required

HardiePlank Lap Siding installation: What should be done with the kickout flashing where the roof meets the wall?

Extend it at least 2 inches beyond the wall

Caulk around it

Paint it to match the siding

Install it flush with the siding

HardiePlank Lap Siding installation: What is the minimum clearance required from the siding to a deck, stoop, porch, or similar structure?

1 inch

2 inches

6 inches

As required by local building codes

HardiePlank Lap Siding installation: What is the correct procedure for installing HardiePlank lap siding in cold climates?

Increase the overlap to 2 inches

Install as usual with no special adjustments

Allow for expansion and contraction due to temperature changes

Preheat the siding before installation

HardiePlank Lap Siding installation: What should be done with the water-resistive barrier at penetrations and junctions?

Overlap it by at least 6 inches

Caulk all penetrations

Install according to local building code requirements

Use a single layer only

HardiePlank Lap Siding installation: What is the minimum clearance required from the siding to a driveway?

1 inch

2 inches

6 inches

As required by local building codes

HardiePlank Lap Siding installation: What should be done with the drip edge to ensure proper performance?

Caulk the bottom edge

Install it at a slight angle

Ensure it is handled with care to prevent damage

Paint it with waterproof paint

HardiePlank Lap Siding installation: What is the minimum clearance required from the siding to a gutter in non-sheltered areas?

1 inch

2 inches

6 inches

No specific requirement